DC switches
Battery tool switches
Model 5-.., 6-.. and
6-..R have identical dimensions, mounting configuration,
trigger and reversing levers.
As a result the same basic tools can be used for different
ratings.
The differences between the switches are defined by the
electronics.
Model
06-.. General Characteristics
|
|
All currently available shapes |
(Electronic) Modules:
-
*On-Off
-
*Single pole
-
*Two speed
-
*Duty cycle
control from 10% - 100%
-
*Power MOSFET to
be mounted on heat sink
-
*Rating of power
MOSFET and capacity of heat sink to be determined for each
application
-
*Electronic torque
control can be provided in the same switch housing
Optional:
-
*Battery clips
-
*Reversing module
-
*Dynamic Brake
-
*Dimensional
adaptor available
Terminals:
-
*Push-in
Approvals:
-
*UL-(55439)
|
|
MODEL |
VOLTS |
FET |
REMARKS |
RECOMMENDED(*) HEATSINK VOLUME |
STANDARD APPLICATION |
APPROVALS |
| Cu |
Al |
| 05-.. |
7.2-9.6V |
25A |
No
freewheel diode |
4 cm³ |
5.7 cm³ |
up to
9.6V Tools (**) |
UL12A |
| 06-.. |
7.2-15V |
25A |
- |
4 cm³ |
5.7 cm³ |
7.2V
Tools |
| 7.2-15V |
25A |
- |
6 cm³ |
8.6 cm³ |
9.6V Tools |
| 9.6-15V |
50A |
- |
6 cm³ |
8.6 cm³ |
12V Tools |
| 9.6-15V |
50A |
- |
8 cm³ |
11.5 cm³ |
14.4V
Tools |
| 9.6-20V |
50A |
Special
electronics |
10cm³ |
14.4 cm³ |
18V Tools |
| 9.6-24V |
70A |
Special
electronics |
10 cm³ |
14.4 cm³ |
24V Tools |
- |
| On/Off 24V |
- |
- |
- |
- |
up to 24V
Tools |
| 06-..R |
7.2-12V |
Internal |
Limited Duty
Cycle |
Internal Heat sink |
7.2V
Tools |
UL12A |
| 7.2-12V |
Internal |
Internal Heat sink |
9.6V Tools |
| 7.2-12V |
Internal |
Internal Heat sink |
12V Tools |
| 12-18V |
Internal |
Wrap-around Heat sink |
14.4V
Tools |
| 12-18V |
Internal |
Wrap-around Heat sink |
18V Tools |
Model
60-.. General Characteristics
|
|
Basic
shapes / dimensions
All
currently available models |
(Electronic) Modules:
-
*On-Off
-
*Single pole
-
*Duty cycle
control from 10% - 100%
-
*Internal power
MOSFET on hybrid
-
*Rating of power
MOSFET and capacity of heat sink to be determined for each
application
Optional:
-
*Battery clips
-
*Reversing module
-
*Dynamic Brake
-
*Dimensional
adaptor available
Terminals:
-
*Soldering eyes or
quick connect tabs
-
*Terminals for
motor and battery connection
Approvals:
-
*UL-(55439)
-
*CSA US (LR-18950)
|
| MODEL |
VOLTS |
MAX.
VARIABLE SPEED DUTY CYCLE |
REMARKS |
STANDARD APPLICATION |
APPROVALS |
|
60-.. |
7.2-15V |
20-30% |
Heat sinking depends on application |
- |
UL 20A / CSA US |
| 35-45% |
- |
| 55-45% |
- |
| 60-80% |
- |
| 100% |
- |
|
15-24V |
20-30% |
Heat sinking depends on application |
- |
UL 20A / CSA US |
| 35-45% |
- |
| 55-45% |
- |
| 60-80% |
- |
| 100% |
- |
| on/off 24V |
- |
- |
- |
- |
General remark:
The CAPAX DC Switch Application Guidelines Manual
supplies additional technical
information for making the optimized selection.
However it is recommended to have the chosen combination approved by CAPAX
Engineering Department.
(*) Volume defined by standard CAPAX test procedure no’s 30.20.30.00 and
30.20.31.00.
Depending on motor- battery conditions and customer requirements, this volume
may vary.
Calculations on request.
(**) Higher voltages possible after application investigation by CAPAX
Engineering Department.